1. <dd id="plmrb"></dd>
      <tbody id="plmrb"><pre id="plmrb"></pre></tbody>

        特種定制鋰電池

        特種定制鋰電池

        特種設備、衛星通訊、戶外勘探、測量,便攜式儲能、軍/警用手持裝備等

        便攜式電站320Wh戶外發電機,110V/500W交流插座和LED手電筒,超級安全的備用鋰電池

        型號編碼:T300-EU/CH/UK/JP
        標稱電壓:400WH
        標稱容量:25Ah
        出廠電壓:12.8V
        執行標準:GB/T 18287-2013
        工作溫度:充電:0~40℃
        產品規格:240*133*201
        產品重量:≈2.4Kg
        開發定制:OEM
        產品描述:本產品是一款便攜式儲能產品;額定輸出總功率約 400W;分別為 AC-200W//PD-45W*1/USB-24W( USB1+USB2)/點煙器 120W ,具有交流(110VAC/200W)、USB-A、Type C、DC(5521)和點煙器 四種不同端口輸出。系

        ??在線下單
        本產品是一款便攜式儲能產品;額定輸出總功率約 400W;分別為 AC-200W//PD-45W*1/USB-24W(
        USB1+USB2)/點煙器
        120W ,具有交流(110VAC/200W)、USB-A、Type C、DC(5521)和點煙器 四種不同端口輸出。系統有直流充電端口,
        可單獨搭配直流光伏、車載直流輸出、AC 適配器 對系統進行充電;PD 接口支持 45W 充電,可使用具備 TYPE-C 接口的
        PD 充電器進行充電。
        • DC INPUT + PD INPUT/OUTPUT )
        DC INPUT
        Item Min Type Max Remark
        Rated Input voltage 10V 15V 25V Whichever Non load or loading
        Rated Input current - 3A 3.5A  
        Rated Input power   45W   Automatic adjustment according input power
        Ripple voltage of charging - - 200mV

        Test from the Input connector, oscilloscope Bandwidth

        setup as 20MHZ, parallel with 10uF and 0.1uF capacitor

        Input over-current protection - - -  
        Input Lower-voltage protection - - 5V  
        Input over-voltage protection 25V - 27V

        The devices will stop charging If the Input voltage

        exceed the protection voltage

        Input port short-circuit protection - - - Stop charging, components no damage
        Input polarity reverse protection - - - Support(not charging if input polarity reverse)
        Input adapter compatibility 10-15 VDC
        Solar panel charging 18-24V with mppt function
        Pass through function The device can support discharging while the product is charging; the Type-C Output power will drop down to 36W if the product charging via DC Input port.
        LCD display of charging Display the charging power and battery capacity
        Battery charging suggestion
        1. Suggestion charging the device every 2 or 3 month;
        2. Self consumption: <2mA

         

        Item Min Type Max Remark

        PD45W

        Charge and Discharge

        4.75V 5.0V 5.5V
        1. PCBA board end voltage;
        2. 5V/9V/12V/15V Rated input/output current:3A

        20V Rated input/output current:2.25A

        8.55V 9V 9.45V
        11.4V 12V 12.6V
        14.25V 15V 15.75V
        19V 20V 21V

        Apple 5V/2.4A

        Charge and Discharge

        4.75V 5.0V 5.25V Protocol: BC1.2 DCP; Apple 2.4A
            2.4A
        Output short circuit protection      

        Turn off discharging

         

         

        • DC (5521)Output features
          Min Type Max Remark
        Output voltage range 10.8V 12.0V 14.6V  
        Allowable output current - 10A -  
        Allowable output power - 120W 146W  
        output current - 10A 12A CV 12V test
        Output ripple - - < 150mV Rated load,oscilloscope Bandwidth setup as 20MHZ, parallel with 10uF and 0.1uF capacitor, the ripple < 800mV while AC Output loading
        Discharging efficiency >92% - - Test requirements: test 4 model average efficiency of 25% 50% 75% 100% of full load; test at PCBA board end.
        Limited current protection 10A - 13A The output will turn off if the output current is exceed specified value; the LCD blink display AC ! while Key’s LED blinking and buzzer is ringing 3 times. The product will recover work normally after cut off the loading and press key button.
        Output over-voltage protection 15V - 16.8V The output will turn off when the product
        doesn't work properly and the output
        voltage is exceed specified value.  
        Short circuit protection - support - The output will turn off and the LCD blink display AC ! while Key’s LED blinking and buzzer is ringing 3 times. The product will recover work normally after cut off the loading and press key button.
                     
        • USB1&2 Output features
        Item Min Type Max Remark  
        Output voltage range 4.75V 5V 5.25V    
        Allowable output current - 2.4A -    
        Allowable output power   12W      
        CC Output 2.1 2.4 2.5A CV 4.75V Test model  
        Output ripple - - < 150mV Rated load,oscilloscope Bandwidth setup as 20MHZ, parallel with 10uF and 0.1uF capacitor,  
        Discharging efficiency >92% - - Test requirements: test 4 model average efficiency of 25% 50% 75% 100% of full load; test at PCBA board end.  
        Limited current protection 2.5A   3A The output will turn off if the output current is exceed specified value;  
        Output over-voltage protection 6.2V - 6.8V The output will turn off when the product doesn't  
          work properly and the output voltage is exceed  
        specified value.    
        Short circuit protection -

        suppor

        t

        - The output will turn off if the output port is short circuit by wire or external devices; the product will be automatically recovery work normally  
                after cutoff the loading.
                         
        Item Min Type Max Remark
        •  
        • AC Sine wave output features:
        Item Min Type Max Remark
        Output voltage range 200V 220V 240V  
        Rated output current - 0.9A -  
        Rated output Power   200W    
        Output frequency 47 Hz 50 Hz 53Hz  
        Non-loading current     600mA  
        Discharging efficiency >85% - - Test requirements: test 4 model average efficiency of 25% 50% 75% 100% of full load; test at PCBA board end.
        Over loading protection 220W - 300W

        The output will turn off if the output power is exceed specified value;

        the LCD blink display AC ! while Key’s LED blinking and buzzer is ringing 3 times. The product will recover work normally after cut off the loading and press key button.

        Over temperature protection Of AC board 80℃ - 100℃ Tthe output will turn off, the product can be recovery work normally after temperature down and press the key button

        Over temperature recovery

        Of AC board

        70℃ - 80℃
        Fan start 55℃   65℃  
        Fan stop 45℃   55℃  
        Short circuit protection -

        suppor

        t

        - The output will turn off and the LCD blink display AC ! while Key’s LED blinking and buzzer is ringing 3 times. The product will recover work normally after cut off the loading and press key button.

        Remark: the fan will stop runing if the the AC board was temperature protection.

        • Automatic power off parameter:
        Item   Min Type Max Remark
        USB1 turn-off current -   80 mA 100 mA  
        USB2 turn-off current -   80 mA 100 mA  
        DC turn-off current -   50mA 80 mA  
        AC turn-off power -   3W 4W  
        TYPE-C turn-off current     50mA 80mA  
        LED light turn-on -   - - The automatic will be not available while LED light is turn on.

        Remark:

        1. Above parameter value only specified for each one port, the connect more than one port, the turn-off current will count all the port of current.
        2. The default setting is turn-on the automatic power off function,the user can press the DC + AC key button for 3S, the buzzer short ringing 2 times, the automatic power off function will be turn-off; press the DC + AC key button for 3S again, the buzzer long ringing 1 time,the automatic power off function will be recovery work normally;
        3. The automatic power off function also be recovery work normally after re turn-on the product After turn off the product ≥10S.

        3.5 LED light function:

        LED Current - 150mA 250 mA  
        LED Voltage - 18V 21V  
        LED Power - 3.6W 5.25W  
        Lamp color temp. - 4500K -  
        Lamp qty.   12    

        4.Battery features:

        No. content Testing method Remark
        1 Charge cut-off voltage 13.8V  
        2 Discharge cut-off voltage 8.8V  
        3 Standard charge

        Under the condition of the ambient temperature of 25±2℃,

        Charge the battery at constant current of 0.2C to reach 13.8V. Then charge the battery at constant 13.8V voltage until the charging current decreasing to 0.02C.

         
        4 Standard discharge After the standard charging,rest for 1 hour then discharge to 8.8V@0.2C.  
        5 Shipments voltage   Quantity of electricity≤30 %
        6

        Maximum Charge

        Current

        ≤12A  
        7

        Maximum

        continuous working current

        ≤30A Instantaneous current≤ 60A time≤2S
        8 Rated capacity

        Typical capacity:250000mAh

        Minimum capacity:24600mAh-5%

        standard

        discharge after standard charge

        9 Operation temperature range charge:0~40℃ humidity:60±25% 60±25%R.H
        discharge:-10~40℃
        10 Storage temperature ≤1 month: -20 ~ 45℃

        60±25%R.H

        Best 10~25℃ for

            ≤3 months: -10 ~ 30℃ long-time storage
        ≤1 year: 0 ~ 30℃
        11 Impedance <80mΩ  
        12 Weight Approx:≈2400g  

        5.Environment features:

        LCD Function Over temperature warning, display the AC ! and buzzer ringing 3 times when temperature protection action
        Display current total charging power, discharging power.
        The key button’s LED blinking during abnormal of AC i protection action
        LED function key button with LED
        Discharge compatibility The specified devices can be quick charge available.
        Working temperature

        Charging: 0-40 °C

        Discharging: -10-40 °C

        Storage temperature -20 ~ 45℃
        Working Humidity 20-90%RH
        Storage Humidity 10-95%RH
        1. Safety features:

        6.1:ESD features:

        ESD
        1. Environment temperature:15~27℃;
        2. Humidity: ≤50%;
        3. Test location: available touched metal and other parts.

        Contact Discharge

        +/-4kv, Normal recovery function allowed

        Air Discharge

        +/-8kv, Normal recovery function allowed

        1. Dielectric Strength :

        Dielectric

        Strength

        (Hi- pot)

        Inverter output L/N VS DC Input

        3000VAC 50Hz/10mA(Max)/60 Second,

        No breakdown and flashover

         

         
        Delivery Time:
         
        - Material Preparation Time: 7-15 days (or inventory)
         
        - Production & Assembly Time 3-10 days
         
        - Testing & Packaging Time: 2-10 days
         
        - Total Delivery Time: 30-45days
         
        - The faster delivery could be negotiable.
         
        Factory photo:
         

         

         



        Contact with our sales team for your OEM and ODM order.
         
        OEM/ODM Service:
        If you want to display your own brand logo in products, bags, labels or anywhere. Or you need to develop battery packs according to your product orientation. Our OEM and ODM services are ready to do it.
         
        Packing:
        According to Stardard Export Packing.
        Carton box, wooden box, wooden pallet

         

        Ryder Electronics established in Shenzhen on July 18, 2005, mainly in the business of battery packs. In 2009 the company passed ISO9001 and improved the product quality standard to fulfill the high-end requirements from our customers.
         
        In 2012, Ryder Electronics moved to a new facility and expend the production capacity, the Productivity improved nearly 10 times than before.
         
        In 2013, Ryder Electronics imported ERP (SAP) system to supervise order execution process.
         
        In 2017, Ryder Electronics expanded the SMT, imported high-speed patch machine from Germany.
         
        Until now the factory grows into a modern enterprise which integrated injection molding, PCB designing, SMT and battery pack assembling services.
         
        In 2018 the company passed ISO14001certification, introduced automated battery production line to further improve the production quality and capacity.



        在線詢價

        用手機掃描二維碼關閉
        二維碼
          1. <dd id="plmrb"></dd>
            <tbody id="plmrb"><pre id="plmrb"></pre></tbody>